涂層耐沾污試驗機是檢測儀器，用于測定各種建筑外墻涂料涂層耐沾污性。
依據相關國際涂層耐沾污試驗方法的有關規定而設計制造的。是涂層耐沾污試驗的沖洗裝置。與反射率配合使用測定涂層耐沾污性。
The coating stain resistance tester is a testing instrument for determining the stain resistance of various building exterior wall coatings.
Designed and manufactured in accordance with the relevant provisions of the relevant international coating resistance test methods. It is a flushing device for the coating stain resistance test. Used in combination with reflectance to determine the coating's stain resistance.
QWX涂層耐沾污試驗機技術參數：
★水箱容積5升，流水管內徑8mm。
★時間控制：0秒—99小時99秒。
★電源電壓：AC220V，50HZ，保險為3A。
★外形尺寸：500X300mm
★重量:56kg
Technical parameters of QWX coating stain resistance tester:
★ The water tank has a volume of 5 liters and the inner diameter of the flow pipe is 8mm.
★ Time control: 0 seconds-99 hours and 99 seconds.
★ Power supply voltage: AC220V, 50HZ, insurance is 3A.
★ Dimensions: 500X300mm
Weight: 56kg
QWX涂層耐沾污試驗機試驗前準備
★將水箱固定，并保證流水管空間基本垂直于水平面，且流水口距試板200mm，將兩節水管按圖連接牢固，螺紋處可用四氟帶纏繞。將水管支架，控制器支架固定，接好上水溢水管。
★將電磁閥引線插入控制器信號孔內，鎖緊螺母在接通用220V電源。（在接通電源開關C前，應先將開關B撥至“暫停"位置）
QWX coating stain resistance tester preparation before test
★ Fix the water tank, and ensure that the space of the water pipe is basically perpendicular to the horizontal plane, and the water outlet is 200mm away from the test plate. Fix the water pipe bracket and controller bracket, and connect the water overflow pipe.
★ Insert the solenoid valve lead into the signal hole of the controller, and the lock nut is connected with 220V power supply. (Before turning on the power switch C, first turn the switch B to the "pause" position)
QWX涂層耐沾污試驗機操作步驟：
★給水箱注水，有溢水即停止上水，溢水停止后將樣板放在樣板架上。
★將時間繼電器自左第三位調至M，**位調至于其余各位調至零，即為1分鐘。將B撥至“暫停"位置，打開電源開關C，在按一下A“清零"。再將B撥至“工作"，此時電磁閥工作，計時開始。亦即沖洗開始。此時應移動樣板，使其各部位都能經過水流點。一分鐘后閥門開關沖水停止。再將B撥至“暫停"，按下復位A鍵。一個試驗過程結束。將水箱在注水等待下一個試驗。
★沖洗后樣板的干燥及反射系數的測定，粉煤灰水的配制，粉煤灰的參數，樣板底材及樣板的制做，按相關規定執行。
Operation steps of QWX coating stain resistance tester:
★ Fill the water tank with water, stop the water supply if there is overflow, and place the sample on the sample frame after the overflow stops.
★ Turn the time relay from the third position to M, and the ** position to zero for the rest of the bits, which is 1 minute. Set B to “pause" position, turn on power switch C, and press A to “zero". Then set B to "Work", at this time the solenoid valve works and the timing starts. The rinsing is started. At this time, the template should be moved so that all parts can pass the water flow point. After one minute, valve flushing stopped. Then dial B to "pause" and press the reset A key. An experimental process ends. Fill the water tank with water and wait for the next test.
★ The measurement of the drying and reflection coefficient of the sample after washing, the preparation of the fly ash water, the parameters of the fly ash, the preparation of the sample substrate and the sample are carried out according to relevant regulations.
QWX涂層耐沾污試驗機結構：
主要由不銹鋼水箱、流水管、樣板架及電磁閥、時間繼電器、等自動控制裝置、水箱支架、控制器支架、管路支架等組成。
QWX coating stain resistance tester structure:
It is mainly composed of stainless steel water tank, water pipe, sample frame and solenoid valve, time relay, and other automatic control devices, water tank bracket, controller bracket, pipeline bracket, etc.
QWX涂層耐沾污試驗機注意事項：
本裝置為水電結合產品，管路連接中不許有漏水現象，否則不能使用，電源處必須有漏電保護裝置，使用后拔掉電源插頭。操作時應濕干分離，并有兩人操作。一個人操作控制器。一個人移動樣板做試驗。
QWX Coating Contamination Tester Note:
This device is a combination of water and electricity. No water leakage is allowed in the pipeline connection, otherwise it cannot be used. The power supply must have a leakage protection device. Unplug the power plug after use. It should be separated by wet and dry operation, and it should be operated by two persons. One person operates the controller. A person moves the template to experiment.
QWX涂層耐沾污試驗機配置清單
1、水箱一臺。
2、水箱支架一套。
3、水管2件。
4、水管支架一套。
5、樣板架一個。
6、控制器及支架一套。
7、塑料水管6米，接口一個。
8、保險管3A一支。
9、說明書1
QWX coating stain resistance tester configuration list
1. One water tank.
2. A set of water tank bracket.
3. 2 water pipes.
4. A set of water pipe support.
5, a model frame.
6. A set of controller and bracket.
7, plastic water pipe 6 meters, one interface.
8. A 3A insurance tube.
9.Instruction 1
會員1.png)
QQ:2568841715
