一、產品簡介：
用于測量地面石材、陶瓷磚、塑料薄膜和薄片、橡膠、紙張、紙板、編織袋等材料滑動時的靜摩擦系數和動摩擦系數。通過測量材料的滑爽性，可以控制調節(jié)材料生產質量工藝指標，滿足產品使用要求。另外還可用于日化用品的滑爽性能測定。采用觸摸屏控制，友好的人機操作界面。儀器內部設有行程限位和正負力值過載保護功能。具有測試速度可調、負荷測量精度高、操作方便等特點。
First, Product introduction:Used to measure the static friction coefficient and dynamic friction coefficient of ground stone, ceramic tile, plastic film and sheet, rubber, paper, cardboard, woven bag and other materials when sliding. By measuring the slip of the material, the quality and process indicators of the material production can be controlled and adjusted to meet product use requirements. In addition, it can also be used to determine the slip performance of daily chemical products. Touch screen control, friendly man-machine operation interface. The instrument is equipped with internal travel limit and positive and negative force value overload protection functions. It has the characteristics of adjustable test speed, high load measurement accuracy and convenient operation.
二、技術參數：
★測力范圍：0-100N、0-200N、0-500N（可選）
★測力精度：0.1
★重塊重量：50N，4.5KG、2700g（可選）
★功率：240W
★電源：220V，
★電動均勻施力。
Technical parameters：
★ Measuring range: 0-100N, 0-200N, 0-500N (optional)
★ Force measurement accuracy: 0.1
★ Heavy weight: 50N, 4.5KG, 2700g (optional)
★ Power: 240W
★ Power: 220V,
★ Electric force is applied uniformly.
三、試驗機配置：
★主機1臺，
★砝碼1件，
★400號碳化硅砂紙2張，
★P220碳化硅粉1包，
★150*150*5mm及100*100*5mm浮法玻璃各1塊。
Third, the test machine configuration:
★ 1 host,
★ 1 weight,
★ 2 pieces of 400 silicon carbide sandpaper,
★ 1 pack of P220 silicon carbide powder,
★ 150 * 150 * 5mm and 100 * 100 * 5mm float glass each.
四、使用方法：
將測試面擦拭干凈,必要時用清水洗凈并干燥,
將測試樣品放在工作臺上,將滑塊組件放在測試面上,調整試樣高度，使滑塊組環(huán)*螺絲與力傳感器處于同于水平。力傳感器掛鉤掛在滑塊組件的環(huán)*螺釘上,在滑塊組件上面的中心位置放置一個50 N的重塊,固定測試樣品,使力傳感器的拉桿和**螺釘保持在同一條水平線上,3秒中內，按試驗鍵，立即緩慢拉動設備至滑塊組件恰好發(fā)生移動,記錄下此時的拉力值,準確至0.1 N,一個測試面上要拉動4次組件,每次與上次方向在水平面上呈90角,每進行一次拉動前就要用400號砂紙對耐磨合成橡膠表面進行一次打磨并保持表面平整。記錄所有讀數。
Method of use
Wipe the test surface clean, rinse with water and dry if necessary.
Place the test sample on the workbench, place the slider assembly on the test surface, and adjust the height of the sample so that the slider group ring * screw and the force sensor are at the same level. The force sensor hook is hung on the ring * screw of the slider assembly, and a 50 N weight is placed at the center position above the slider assembly to fix the test sample, so that the lever of the force sensor and the screw are kept on the same horizontal line. Within 3 seconds, press the test button, and immediately slowly pull the device until the slider assembly just moves. Record the pulling force at this time, accurate to 0.1 N. Pull the component 4 times on a test surface, each time with the last direction. At a 90-degree angle on the horizontal plane, the surface of the wear-resistant synthetic rubber must be polished with 400-grit sandpaper before each pull and keep the surface flat. Record all readings.
